Savin 7700W Manuale Utente

Operating InstructionsZfbh010e.epsRead this manual carefully before you use this product and keep it handy for futurereference.For safety, please foll

viii

1Guide to ComponentsCopier Exterior1.LocksSqueeze both locks(1a&1b) to open theunit. Open the unit to empty the usedtoner bottle and to remove jam

211.Main switchUse this switch to turn the copier on andoff. The copier will need about 3 minutesto warm up, if it's been turned off for along ti

3Operation Panel1.Function indicatorsThese indicators show which setting youare currently editing, Press the Functionkey to cycle through them.• The t

411. {{{{Function Select}}}} keyPress to change which setting you are ed-iting. The current selection is shown bythe indicators above the key:•Paper L

51. BasicsTurning on the PowerTo turn the machine on, press themain switch.Turn On the Main PowerAMake sure that the power cord isfirmly plugged into

Basics61Recommended Originals• You can set originals with weight in the range 21g/m2 (6 lb) to 157 g/m2 (41lb).• You can set original with sizes betwe

Recommended Originals71Non-recommended Originals• The following types of originals are not recommended.• Wet originals• Originals with cardboard stuck

Basics81Recommended Paper• Standard paper sizes that can be used in this copier are shown below.• When you make a copy on a non-standard size of paper

Recommended Paper91• When you use paper in high humidity under hot conditions, take out only thenecessary amount of paper from the bag. Do not take al

Where symbols are used on or near switches, they mean an under in accordance with IEC 60417:aaaa means POWER ON.cccc means STAND BY.Copyright © 2001 R

Basics101TonerHandling TonerR WARNING:R CAUTION:R CAUTION:• If you use toner other than that recommended, a fault might occur.• If you want to add ton

112. CopyingBasic Copying (Copying to sheets)Use bypass table or roll feeder to copy onto paper.Note❒ For acceptable types of original and paper,⇒ P.6

Copying122ATurn on the main switch.BMake sure that the Wait indicator goes off, and then Ready and the Set Pa-per indicator go on.Make sure that the

Basic Copying (Copying to sheets)132ESlide the paper straight into the copier until it stops. The copier will soonpull it in.Note❒ Center the paper fa

Copying142The copy is delivered from the slot on top of the copier (B).If you make several copies of the same original, when the copy comes out, re-mo

Basic Copying (Copying to sheets)152Using the Roll Feeder (Option)AWhen the Wait indicator goes off and the Ready and the Set Paper indicatorgo on, th

Copying162EMake sure that the Set Original indicator goes on.FSet the original guides to match the width of the original.GCenter your original face up

Basic Copying (Copying to sheets)172HThe original comes from the opening just under the Original Table (AAAA).The copy is delivered from the slot on t

Copying182DInsert the original face down from the rear table.EHold and take the original which has been read and delivered in the frontof the copier.

Copying onto Roll Paper (Option)192Copying onto Roll Paper (Option)The paper will be fed to the copier from the Roll Feeder. You can copy onto rollpap

iSafety InformationWhen using your equipment, the following safety precautions should always befollowed.Safety During OperationIn this manual, the fol

Copying202❒ If you set the number of copies, Semi Synchro Cut can handle automaticallyby the length at your setting for first copy.❒ Do not use carrie

Copying onto Roll Paper (Option)212EPress the {{{{Paper Feed}}}} key.FSet the original guides to match the width of the original.GCenter your origina

Copying222HJust as the trailing edge of the original passes the table edge, press the {{{{RFSelect/Cut}}}} key.Important❒ To cancel copying, press the

Copying onto Roll Paper (Option)232APress the {{{{Preset Cut}}}} key (1). The Preset/Variable indicator lights up (2) and the Paper Length displayshow

Copying242APress the {{{{Preset Cut}}}} key(1). The Preset/Variable indicator(2) lights up andthe "Paper Length" display shows the default P

Copying onto Roll Paper (Option)252Using The Roll Cutting Rail (Option)The Roll Cutting Rail allows you to use roll paper and cut your own sheets. For

Copying262DWith your other hand, insert the blade of a paper knife between the tworods and slide across the length of the rail.EMake your copy as show

273. Copy SettingsCopying Onto Other MediaTo copy onto translucent or tracing paper or film, use the {Copy Media} key tomatch the paper type refer to

Copy Settings283Adjusting the Fusing Temperature ManuallyAPress the {{{{Copy Media}}}} key to turn on the Translucent or Film indicator thatyou want.B

Adjusting Copy Image Density293Adjusting Copy Image DensityTo make copies darker or lighter, change the density setting. There are 14 densi-ty levels

iiR WARNING: • Connect the power cord directly into a wall outlet and never use an extension cord.• Only connect the machine to the power source descr

Copy Settings303Making Several Copies of the Same OriginalYou can preset the number of copies (1 to 99) you want to make. Repeated cop-ying means maki

Setting a Leading Edge Margin313Setting a Leading Edge MarginYou can set a margin at the leading edge of the copy.Note❒ You can set up to a ±99mm, ±4.

Copy Settings323Partial CopyingThe Partial Copy function copies only a part of an original.You need to enter start and end points in the feed directio

Partial Copying333BSlide the paper straight into the copier until it stops, or press the {{{{RF Select/Cut}}}} key to turn on the RF Select indicator.

Copy Settings343The "P" will disappear.

Programming Settings You Often Use353Programming Settings You Often UseThere are two ways of programming settings you often use.A) Store the settings

Copy Settings363Recalling Settings Stored in the Program keyAPress the {{{{Program}}}} key before copying.BEnter the number of copies required with th

Programming Settings You Often Use373DTurn off the main switch.Note❒ The next time you turn the copier on, the settings you programmed in stepC will t

Copy Settings383User ToolsAccess the User Tools to make the following adjustments:A1) Not in useA2) Semi Synchro Cut Adjustment; Allows you to adjust

User Tools393DUse the {{{{+}}}} and {{{{−−−−}}}} key to change the value.EPress the {{{{Program}}}} key to return to step BBBB.FPress the {{{{Clear Mo

iiiR CAUTION: • When you pull out the plug from the socket, grip the plug to avoid damaging the cord and causing fire or electric shock.• Unplug the p

Copy Settings403Settings You Can Change with User ToolsThis section is for the key operators in charge of this machine. You can changeor set the machi

Settings You Can Change with User Tools413❒ Default: 0• Beeper On/Off(+05): The beeper can be turned off completely; turned off forsetting the margin,

Copy Settings423• Auto Energy Saver Mode(+10): The fusing unit needs to be hot for copying.When the copier is idle, the fusing unit can be kept hot to

Settings You Can Change with User Tools433• Semi-synchro Cut Original Scanning Mode(+18): Selects whether the rollpaper cut key must be pressed at the

Copy Settings443Note❒ 0: Standard Density 1: Darker Image Density❒ Default: 0

454. Maintaining Your CopierChanging The Used Toner BottleWhen E is displayed, it is time to change the toner bottle.R WARNING:R CAUTION:R CAUTION:Not

Maintaining Your Copier464BUnplug the code from the machine.COpen the door on the right side of the copier, and then carefully remove theplastic bottl

Changing The Used Toner Bottle474FClose the upper unit.

Maintaining Your Copier484Adding TonerWhen D is displayed, it is time to add toner.When the indicator starts blinking, you can still copy about 53 fee

Adding Toner494BOpen the toner cartridge cover.CTurn the old cartridge towards you.Then, while pressing the cartridge to the right (A ), lift the left

ivENERGY STAR Program• Auto Off ModeTo conserve energy, this product automatically turns off 1 minutes after thelast copying or printing job has been

Maintaining Your Copier504Make sure the cartridge is set well but don't push it in yet.GTake the right edge of the seal and slowly remove it.HPus

Adding Toner514The copier will need a few moments to warm up before it is ready to copy.

Maintaining Your Copier524Changing The Roll Paper SizeChange the size guides on the left andright of the roll paper holder whenyou load different size

Changing The Roll Paper Size534Metric version Roll FeederA0 KA1 KLA2 KLA3 KLA4 K

Maintaining Your Copier544Loading A Roll Of PaperWhen C is displayed, it is time to install a new roll of paper.R CAUTION:Important❒ When removing pap

Loading A Roll Of Paper554CRaise the lever on the paper holder (AAAA), and then pull out the roll holderfrom the empty core (BBBB).DSet the paper hold

Maintaining Your Copier564❒ If applicable, adjust the roll paper position and lock the lever.❒ You may hardly to adjust the roll paper position when

Loading A Roll Of Paper574Note❒ Do not hold the paper knob from side. It may cause you touching a stickyoil. For how to turn the knob without any harm

Maintaining Your Copier584IClose the Roll Feeder.

Loading A New Roll Onto Paper Cutting Rail (Option)594Loading A New Roll Onto Paper Cutting Rail (Option)ALift the rail.BRemove the spool from its sup

vHow to Read this ManualSymbolsIn this manual, the following symbols are used:R WARNING:This symbol indicates a potentially hazardous situation that m

Maintaining Your Copier604DSlide the new roll on the spool and put the cap over the end of the roll.EPlace the spool on the holder so that the paper r

615. TroubleshootingIf Something Goes WrongIf you have problems with your copier, consult the following pages. If a serviceindicator lights up, read t

Troubleshooting625If Jams OccurIf the Original is Jammed at the ExitNote❒ If the paper or original gets stuck in the copier, remove both original and

If Jams Occur635If Sheet Paper is Jammed in the Feed-in SlotR CAUTION:ASqueeze the locks on each side of the copier and lift the unit.BPull out the co

Troubleshooting645If Sheet Paper is Jammed at the Paper ExitR CAUTION:ASqueeze the locks on each side of the copier and lift the moddle unit be-tween

If Jams Occur655DClose the unit and all covers. Press firmly on both sides until it clicks intoplace.If Roll Paper JamsIf roll paper jams anywhere in

Troubleshooting665Note❒ Slide the cutter one way only, otherwise paper waste may pile up insidethe machine.DRotate the paper roll in the direction of

If Jams Occur675❒ Make sure that the paper is not loose. Insert it straight into the roller.❒ Watch carefully to make sure that the flap of the paper

Troubleshooting685DHold the paper (BBBB ), and then slide the cutter (AAAA).Note❒ Slide the cutter one way only, otherwise paper waste may pile up ins

If Jams Occur695❒ Watch carefully to make sure that the flap of the paper is inserted betweenfeeder and the roller.GClose the Roll Feeder.

viTABLE OF CONTENTSGuide to Components... 1Copier Exterior...

Troubleshooting705OthersIf a puzzling or recurring problem occurs, check the following before calling aservice representative. It's also a good i

Others715Creases• Try setting your copy paper sideways.• If long creases appear on copies, try setting your copy paper sideways, or trychanging the co

Troubleshooting725Daily MaintenanceClean the Exposure Glass & the Platen Plateyou should clean the copy and original tables with a damp cloth, the

Do's & Don'ts735Do's & Don'tsR CAUTION:• Do not touch areas on or around the fusing unit. These areas get hot.• After copi

Troubleshooting745Where to Put Your CopierYour copier should be installed by a qualified technician. If you need to trans-port your copier to a distan

Where to Put Your Copier755• Areas prone to strong vibrations• Locations directly exposed to cool air from an air conditioner or heat from anearby hea

Troubleshooting765• Make sure the power outlet is close to the copier and easily accessible at alltimes.Access To MachinePlace the copier near a power

776. SpecificationsCopierConfiguration DesktopProcess Dry electrostatic transfer systemScanning Original moving over a fixed fiber optics arrayOrigina

Specifications786Options• Roll feeder• Side Guide Type 770• Table Type 770• Roll Cutting Rail Type 770Number of loaded paper rolls1 roll (Type 780A) 2

79INDEXAAbsolutely nothing happens, 70Access To Machine, 76Adding Toner, 48Adjusting Copy Image Density, 29Adjusting the Fusing Temperature Ma

viiSettings You Can Change with User Tools.... 404.Maintaining Your CopierChanging The Used Toner Bottle...

80SSafety Information, iSemi Synchro cutting, 19Setting a Leading Edge Margin, 31Settings You Can Change with User Tools, 40Setting the Roll P